The Galaxy Watch Sensor Cover Disappeared and Was Fixed (With Images)

One of the many features that come standard on Samsung watches is a sensor that may be used for a variety of purposes. There is no question that Samsung’s sensors are the finest on the market, but the cover that safeguards the sensor doesn’t seem like it will live up to expectations.

The majority of watch owners have mentioned that after a few months of usage, the sensor cover on their watch eventually comes off. Many people have been unsuccessful in their search for a long-term solution to this issue. Following some consideration, I have formulated an answer to the problem.

During my studies, I also discovered that this issue is pretty prevalent across the board for all of the Galaxy Watch product lines. The query “Why does the Galaxy Watch sensor cover constantly fall?” is one of the most frequently asked questions.

When you immediately put on your watch after applying moisturizer to your wrist, the concentration of the adhesive on the band is reduced, which increases the likelihood that the sensor cover may come loose. In addition to this, the process of charging your watch produces heat, which lowers the adhesive’s concentration. As a direct consequence of this, the sensor cover continues to collapse.

The following Samsung Galaxy Watch models are compatible with this software update:

  • Galaxy Watch
  • The Galaxy Watch in Active Mode
  • Both the Galaxy Watch Active 2 and the Galaxy Watch 3
  • Samsung Galaxy Watch 4

Warning: Before you begin, please make sure you have thoroughly read all of the procedures in order to prevent making any kind of error (Highly Recommended).

Listing of Contents (Table of)

  • Instructions on How to Replace the Sensor Cover on Your Samsung Galaxy Watch
  1. First, obtain the appropriate substitute component.
  2. Step 2: Set the watch to the Stopped mode.
  3. Step 3: Get Rid of Any Old Adhesive
  4. The fourth step is to adhere the cover to the adhesive.
  5. The next step is to attach the new sensor cover to the watch, and then you’re finished!
  • Advice on How to Avoid Issues with the Galaxy Watch Sensor Cover

Instructions on How to Replace the Sensor Cover on Your Samsung Galaxy Watch

First, obtain the appropriate substitute component.

Be certain that you have the sensor replacement component on hand before beginning the procedure of replacement. EagleWireless’ Back Rear Lens Glass is compatible with the Galaxy Watch Active 2, Galaxy Watch 3, and Galaxy Watch 4 models.

If you have a Galaxy Watch Active, you should look into purchasing this Eaglewireless Rear Glass Panel since it is the one that is compatible with your wearable device.

Additionally, the majority of users have the misconception that the sensor cover on the Galaxy Watch Active is the same as the one on the Galaxy Watch. However, that is not the case. The sensor covers on each of them are different.

Because of this, the Ubrokeifixit Back Rear Lens Glass is the one that is compatible with the Galaxy Watch.

In addition, the replacement component for your cover may come with an adhesive sticker in the shape of a red circle (shown in the figure to the right), which will come in handy when it comes time to adhere the cover.

Step 2: Make sure the watch is turned off.

Turn off your Samsung Watch after you have the new component in your possession.

When you press and hold the home button for three seconds on the majority of Galaxy Watch models, you’ll feel a tiny vibration when the “Power off” icon displays on the screen. You may turn it off by tapping on it.

You may also see the power-off sign if you pull down the notification panel. This is a different method. To switch off the watch, tap on the button.

The next step is to remove any old adhesive.

While the previous sensor cover is being removed, use wet wipes to clean the rear surface of the Galaxy Watch and completely remove any remnants of the old glue. Check to see that the HR sensor on the smartwatch does not sustain any harm.

The fourth step is to adhere the cover to the adhesive.

You’re nearly done!

Your rear cover replacement component (which is indicated as 1) also includes a circle adhesive in a bright red color (which is marked as 2) so that you may adhere the two pieces together. This is very important since it will make it easier for you to bind the rear cover with the back housing later on.

The sticky component has a red film on the outside; to remove it, just peel it off. The next step is to remove the layer on the rear of the back cover by pulling the red section that is marked with the number 1 outward.

Once the aperture has been unlocked, you may then adhere the cover to the adhesive. Tap on it repeatedly with only your fingertip so that it will properly attach. At long last, remove the clear layer of glue by peeling it off.

The next step is to attach the new sensor cover to the watch, and then you’re finished!

As soon as you are ready, you should connect the new back to the housing for the back.

A helpful hint is to put some weight on the smartwatch and then wrap it in tissue paper or a fabric made of synthetic fibers. Do this for a couple of hours. After a few hours, your smartwatch will function exactly the same way it did when it was brand new and straight from the factory.

Well done! You have successfully replaced the sensor cover for the Samsung Galaxy Watch.

Galaxy Watch: How to Replace the Cover for the Sensors.

Advice on How to Avoid Issues with the Galaxy Watch Sensor Cover

Keep the Moisturizer Away from the Watch The majority of individuals put their watches on right after they apply moisturizer to their wrists, but you should avoid doing this. In the beginning, they won’t have any issues to deal with. This, over time, will cause the concentration of the adhesive to break. The same may be said about water as well.

You may charge your watch in a room with an air conditioner: When you set your watch in the charging position, it produces some amount of heat, which, over time, causes the adhesive to melt. If you want to avoid this problem, make sure that your watch is charging in a room that has air conditioning.

Leave a Reply